Part Number Hot Search : 
MNTWG LTCZQ TDA73480 1DTT1 MC9S1 MC33364 C100B 7C138
Product Description
Full Text Search
 

To Download IDT71V67703 Datasheet File

  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
 
 


  Datasheet File OCR Text:
 256K X 36, 512K X 18 IDT71V67703 3.3V Synchronous SRAMs IDT71V67903 3.3V I/O, Burst Counter Flow-Through Outputs, Single Cycle Deselect Features
x x
x x
x x x x
256K x 36, 512K x 18 memory configurations Supports fast access times: - 7.5ns up to 117MHz clock frequency - 8.0ns up to 100MHz clock frequency - 8.5ns up to 87MHz clock frequency LBO input selects interleaved or linear burst mode Self-timed write cycle with global write control (GW), byte write enable (BWE), and byte writes (BWx) 3.3V core power supply Power down controlled by ZZ input 3.3V I/O supply (VDDQ) Packaged in a JEDEC Standard 100-pin thin plastic quad flatpack (TQFP), 119 ball grid array (BGA) and 165 fine pitch ball grid array (fBGA).
Description
The IDT71V67703/7903 are high-speed SRAMs organized as 256K x 36/512K x 18. The IDT71V67703/7903 SRAMs contain write,
data, address and control registers. There are no registers in the data output path (flow-through architecture). Internal logic allows the SRAM to generate a self-timed write based upon a decision which can be left until the end of the write cycle. The burst mode feature offers the highest level of performance to the system designer, as the IDT71V67703/7903 can provide four cycles of data for a single address presented to the SRAM. An internal burst address counter accepts the first cycle address from the processor, initiating the access sequence. The first cycle of output data will flow-through from the array after a clock-to-data access time delay from the rising clock edge of the same cycle. If burst mode operation is selected (ADV=LOW), the subsequent three cycles of output data will be available to the user on the next three rising clock edges. The order of these three addresses are defined by the internal burst counter and the LBO input pin. The IDT71V67703/7903 SRAMs utilize IDT's latest high-performance CMOS process and are packaged in a JEDEC standard 14mm x 20mm 100-pin thin plastic quad flatpack (TQFP) as well as a 119 ball grid array (BGA) and a 165 fine pitch ball grid array (fBGA).
Pin Description Summary
A0-A18 CE CS0, CS1 OE GW BWE BW1, BW2, BW3, BW4(1) CLK ADV ADSC ADSP LBO ZZ I/O0-I/O31, I/OP1-I/OP4 VDD, VDDQ VSS Address Inputs Chip Enable Chip Selects Output Enable Global Write Enable Byte Write Enable Individual Byte Write Selects Clock Burst Address Advance Address Status (Cache Controller) Address Status (Processor) Linear / Interleaved Burst Order Sleep Mode Data Input / Output Core Power, I/O Power Ground Input Input Input Input Input Input Input Input Input Input Input Input Input I/O Supply Supply Synchronous Synchronous Synchronous Asynchronous Synchronous Synchronous Synchronous N/A Synchronous Synchronous Synchronous DC Asynchronous Synchronous N/A N/A
5309 tbl 01
NOTE: 1. BW3 and BW4 are not applicable for the IDT71V67903.
APRIL 2003
1
(c)2002 Integrated Device Technology, Inc. DSC-5309/04
IDT71V67703, IDT71V67903, 256K x 36, 512K x 18, 3.3V Synchronous SRAMS with 3.3V I/O, Flow-Through Outputs, Single Cycle Deselect Commercial and Industrial Temperature Ranges
Pin Definitions(1)
Symbol A0-A18 ADSC ADSP ADV Pin Function Address Inputs Address Status (Cache Controller) Address Status (Processor) Burst Address Advance Byte Write Enable I/O I I I I Active N/A LOW LOW LOW Description Synchronous Address inputs. The address register is triggered by a combi-nation of the rising e dge of CLK and ADSC Low or ADSP Low and CE Low. Synchronous Address Status from Cache Controller. ADSC is an active LOW input that is used to load the address registers with new addresses. Synchronous Address Status from Processor. ADSP is an active LOW input that is used to load the address registers with new addresses. ADSP is gated by CE. Synchronous Address Advance. ADV is an active LOW input that is used to advance the internal burst counter, controlling burst access after the initial address is loaded. When the inp ut is HIGH the burst counter is not incremented; that is, there is no address advance. Synchronous byte write enable gates the byte write inputs BW1-BW4. If BWE is LOW at the rising edge of CLK then BWx inputs are passed to the next stage in the circuit. If BWE is HIGH then the byte write inputs are blocked and only GW can initiate a write cycle. Synchronous byte write enables. BW1 controls I/O0-7, I/OP1, BW2 controls I/O8-15, I/OP2, etc. Any active byte write causes all outputs to be disabled. Synchronous chip enable. CE is used with CS0 and CS1 to enable the IDT71V67703/7903. CE also gates ADSP. This is the clock input. All timing references for the device are made with respect to this input. Synchronous active HIGH chip select. CS0 is used with CE and CS1 to enable the chip. Synchrono us active LOW chip select. CS1 is used with CE and CS0 to enable the chip. Synchronous global write enable. This input will write all four 9-bit data bytes when LOW on the rising edge of CLK. GW supersedes individual byte write enables. Synchronous data input/output (I/O) pins. The data input path is registered, triggered by the rising edge of CLK. The data output path is flow-through (no output register). Asynchro nous burst order selection input. When LBO is HIGH, the inter-leaved burst sequence is selected. When LBO is LOW the Linear burst sequence is selected. LBO is a static input and must not change state while the device is operating. Asynchronous output enable. When OE is LOW the data output drivers are enabled on the I/O pins if the chip is also selected. When OE is HIGH the I/O pins are in a highimpedance state. 3.3V core power supply. 3.3V I/O Supply. Ground. NC pins are not electrically connected to the device. Asynchronous sleep mode input. ZZ HIGH will gate the CLK internally and power down the IDT71V67703/7903 to its lowest power consumption level. Data retention is guaranteed in Sleep Mode.
5309 tbl 02
BWE
I
LOW
BW1-BW4 CE CLK CS0 CS1 GW I/O0-I/O31 I/OP1-I/OP4 LBO
Individual Byte Write Enables Chip Enable Clock Chip Select 0 Chip Select 1 Global Write Enable Data Input/Output Linear Burst Order
I I I I I I I/O I
LOW LOW N/A HIGH LOW LOW N/A LOW
OE
Output Enable
I
LOW
VDD VDDQ VSS NC ZZ
Power Supply Power Supply Ground No Connect Sleep Mode
N/A N/A N/A N/A 1
N/A N/A N/A N/A HIGH
NOTE: 1. All synchronous inputs must meet specified setup and hold times with respect to CLK.
6.42 2
IDT71V67703, IDT71V67903, 256K x 36, 512K x 18, 3.3V Synchronous SRAMS with 3.3V I/O, Flow-Through Outputs, Single Cycle Deselect Commercial and Industrial Temperature Ranges
Functional Block Diagram
LBO ADV
CEN Burst Sequence INTERNAL ADDRESS
CLK ADSC ADSP
CLK EN Binary Counter CLR
2
Burst Logic
18/19 A0* A1*
Q0 Q1
256K x 36/ 512K x 18BIT MEMORY ARRAY
2 A0,A1 18/19 A2 - A18 36/18 36/18
A0-A17/18 GW BWE BW1
ADDRESS REGISTER Byte 1 Write Register
Byte 1 Write Driver
9
Byte 2 Write Register Byte 2 Write Driver
BW2
Byte 3 Write Register
9
Byte 3 Write Driver
BW3
Byte 4 Write Register
9
Byte 4 Write Driver
BW4
9
CE CS0 CS1
D
Q Enable Register
DATA INPUT REGISTER
CLK EN
ZZ
Powerdown
OE
OE I/O0-I/O31 I/OP1-I/OP4
36/18
OUTPUT BUFFER
,
5309 drw 01
6.42 3
IDT71V67703, IDT71V67903, 256K x 36, 512K x 18, 3.3V Synchronous SRAMS with 3.3V I/O, Flow-Through Outputs, Single Cycle Deselect Commercial and Industrial Temperature Ranges
Absolute Maximum Ratings(1)
Symbol VTERM
(2)
Rating Terminal Voltage with Respect to GND Terminal Voltage with Respect to GND Terminal Voltage with Respect to GND Terminal Voltage with Respect to GND Operating Temperature Temperature Under Bias Storage Temperature Power Dissipation DC Output Current
Commercial -0.5 to +4.6 -0.5 to VDD -0.5 to VDD +0.5 -0.5 to VDDQ +0.5 -0 to +70 -55 to +125 -55 to +125 2.0 50
Unit V V V V
o
Recommended Operating Temperature Supply Voltage
Grade Commercial Industrial Temperature(1) 0C to +70C -40C to +85C VSS 0V 0V VDD 3.3V5% 3.3V5% VDDQ 3.3V5% 3.3V5%
5309 tbl 04
VTERM(3,6) VTERM(4,6) VTERM(5,6) TA
(7)
NOTE: 1. TA is the "instant on" case temperature.
C C C
Recommended DC Operating Conditions
Symbol Parameter Core Supply Voltage I/O Supply Voltage Supply Voltage Input High Voltage - Inputs Input High Voltage - I/O Input Low Voltage Min. 3.135 3.135 0 2.0 2.0 -0.3
(1)
Typ. 3.3 3.3 0
____ ____ ____
Max. 3.465 3.465 0 VDD +0.3 VDDQ +0.3 0.8
Unit V V V V V V
5309 tbl 05
TBIAS TSTG PT IOUT
o
VDD VDDQ VSS
o
W mA
5309 tbl 03
VIH VIH VIL
NOTES: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 2. VDD terminals only. 3. VDDQ terminals only. 4. Input terminals only. 5. I/O terminals only. 6. This is a steady-state DC parameter that applies after the power supplies have ramped up. Power supply sequencing is not necessary; however, the voltage on any input or I/O pin cannot exceed VDDQ during power supply ramp up. 7. TA is the "instant on" case temperature.
NOTE: 1. VIL (min) = -1.0V for pulse width less than tCYC/2, once per cycle.
100-Pin TQFP Capacitance
(TA = +25 C, f = 1.0MHz)
Symbol CIN CI/O Parameter(1) Input Capacitance I/O Capacitance Conditions VIN = 3dV VOUT = 3dV Max. 5 7 Unit pF pF
5309 tbl 07
165 fBGA Capacitance
(TA = +25 C, f = 1.0MHz)
Symbol CIN CI/O Parameter(1) Input Capacitance I/O Capacitance Conditions VIN = 3dV VOUT = 3dV Max. 7 7 Unit pF pF
5309 tbl 07b
119 BGA Capacitance
(TA = +25 C, f = 1.0MHz)
Symbol CIN CI/O Parameter(1) Input Capacitance I/O Capacitance Conditions VIN = 3dV VOUT = 3dV Max. 7 7
Unit pF pF
5309 tbl 07a
NOTE: 1. This parameter is guaranteed by device characterization, but not production tested.
6.42 4
IDT71V67703, IDT71V67903, 256K x 36, 512K x 18, 3.3V Synchronous SRAMS with 3.3V I/O, Flow-Through Outputs, Single Cycle Deselect Commercial and Industrial Temperature Ranges
Pin Configuration 256K x 36, 100-Pin TQFP
A6 A7 CE CS0 BW4 BW3 BW2 BW1 CS1 VDD VSS CLK GW BWE OE ADSC ADSP ADV A8 A9
100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81
I/OP3 I/O16 I/O17 VDDQ VSS I/O18 I/O19 I/O20 I/O21 VSS VDDQ I/O22 I/O23 VSS(1) VDD NC VSS I/O24 I/O25 VDDQ VSS I/O26 I/O27 I/O28 I/O29 VSS VDDQ I/O30 I/O31 I/OP4
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51
I/OP2 I/O15 I/O14 VDDQ VSS I/O13 I/O12 I/O11 I/O10 VSS VDDQ I/O9 I/O8 VSS NC VDD ZZ(2) I/O7 I/O6 VDDQ VSS I/O5 I/O4 I/O3 I/O2 VSS VDDQ I/O1 I/O0 I/OP1
5309 drw 02a
,
LBO A5 A4 A3 A2 A1 A0
Top View
NOTES: 1. Pin 14 does not have to be directly connected to VSS as long as the input voltage is < VIL. 2. Pin 64 can be left unconnected and the device will always remain in active mode.
NC NC VSS VDD
6.42 5
NC A17 A10 A11 A12 A13 A14 A15 A16
IDT71V67703, IDT71V67903, 256K x 36, 512K x 18, 3.3V Synchronous SRAMS with 3.3V I/O, Flow-Through Outputs, Single Cycle Deselect Commercial and Industrial Temperature Ranges
Pin Configuration 512K x 18, 100-Pin TQFP
A6 A7 CE CS0 NC NC BW2 BW1 CS1 VDD VSS CLK GW BWE OE ADSC ADSP ADV A8 A9
100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81
NC NC NC VDDQ VSS NC NC I/O8 I/O9 VSS VDDQ I/O10 I/O11 VSS(1) VDD NC VSS I/O12 I/O13 VDDQ VSS I/O14 I/O15 I/OP2 NC VSS VDDQ NC NC NC
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51
A10 NC NC VDDQ VSS NC I/OP1 I/O7 I/O6 VSS VDDQ I/O5 I/O4 VSS NC VDD ZZ(2) I/O3 I/O2 VDDQ VSS I/O1 I/O0 NC NC VSS VDDQ NC NC NC
5309 drw 02b
,
NOTES: 1. Pin 14 does not have to be directly connected to VSS as long as the input voltage is < VIL. 2. Pin 64 can be left unconnected and the device will always remain in active mode.
LBO A5 A4 A3 A2 A1 A0 NC NC VSS VDD NC A18 A11 A12 A13 A14 A15 A16 A17
Top View
6.42 6
IDT71V67703, IDT71V67903, 256K x 36, 512K x 18, 3.3V Synchronous SRAMS with 3.3V I/O, Flow-Through Outputs, Single Cycle Deselect Commercial and Industrial Temperature Ranges
Pin Configuration 256K x 36, 119 BGA
1 A B C D E F G H J K L M N P R T U VDDQ NC NC I/O16 I/O17 VDDQ I/O20 I/O22 VDDQ I/O24 I/O25 VDDQ I/O29 I/O31 NC NC VDDQ 2 A6 CS0(4) A7 I/OP3 I/O18 I/O19 I/O21 I/O23 VDD I/O26 I/O27 I/O28 I/O30 I/OP4 A5 NC DNU(3) 3 A4 A3 A2 VSS VSS VSS BW3 VSS NC VSS BW4 VSS VSS VSS LBO A10 DNU(3) 4 ADSP ADSC VDD NC CE OE ADV GW VDD CLK NC BWE A1 A0 VDD A11 DNU(3) 5 A8 A9 A12 VSS VSS VSS BW2 VSS NC VSS BW1 VSS VSS VSS VSS(1) A14 DNU(3) 6 A16 A17 A15 I/OP2 I/O13 I/O12 I/O11 I/O9 VDD I/O6 I/O4 I/O3 I/O2 I/O0 A13 NC DNU(3) 7 VDDQ NC NC I/O15 I/O14 VDDQ I/O10 I/O8 VDDQ I/O7 I/O5 VDDQ I/O1 I/OP1 NC ZZ(2) VDDQ
5309 drw 02c
Top View Pin Configuration 512K x 18, 119 BGA
1 A B C D E F G H J K L M N P R T U VDDQ NC NC I/O8 NC VDDQ NC I/O11 VDDQ NC I/O13 VDDQ I/O15 NC NC NC VDDQ 2 A6 CS0 A7 NC I/O9 NC I/O10 NC VDD I/O12 NC I/O14 NC I/OP2 A5 A10 DNU(3)
(4)
3 A4 A3 A2 VSS VSS VSS BW2 VSS NC VSS VSS VSS VSS VSS LBO A15 DNU(3)
4 ADSP ADSC VDD NC CE OE ADV GW VDD CLK NC BWE A1 A0 VDD NC DNU(3)
5 A8 A9 A13 VSS VSS VSS VSS VSS NC VSS BW1 VSS VSS VSS VSS(1) A14 DNU(3)
6 A16 A18 A17 I/O7 NC I/O5 NC I/O3 VDD NC I/O1 NC I/O0 NC A12 A11 DNU(3)
7 VDDQ NC NC NC I/O6 VDDQ I/O4 NC VDDQ I/O2 NC VDDQ NC I/OP1 NC ZZ(2) VDDQ
5309 drw 02d
,
Top View
NOTES: 1. R5 does not have to be directly connected to VSS as long as the input voltage is < VIL. 2. T7 can be left unconnected and the device will always remain in active mode. 3. DNU= Do not use; these signals can either be left unconnected or tied to Vss. 4. On future 18M devices CS0 will be removed, B2 will be used for address expansion.
6.42 7
IDT71V67703, IDT71V67903, 256K x 36, 512K x 18, 3.3V Synchronous SRAMS with 3.3V I/O, Flow-Through Outputs, Single Cycle Deselect Commercial and Industrial Temperature Ranges
Pin Configuration 256K x 36, 165 fBGA
1 A B C D E F G H J K L M N P R NC
(3)
2 A7 A6 NC I/O16 I/O18 I/O20 I/O22 NC I/O24 I/O26 I/O28 I/O30 NC NC
(3)
3 CE CS0 VDDQ VDDQ VDDQ VDDQ VDDQ NC VDDQ VDDQ VDDQ VDDQ VDDQ A5 A4
4 BW3 BW4 VSS VDD VDD VDD VDD VDD VDD VDD VDD VDD VSS A2 A3
5 BW2 BW1 VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS NC DNU
(4)
6 CS1 CLK VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS NC(3) A1 A0
7 BWE GW VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS NC DNU
(4)
8 ADSC OE VSS VDD VDD VDD VDD VDD VDD VDD VDD VDD VSS A10 A11
9 ADV ADSP VDDQ VDDQ VDDQ VDDQ VDDQ NC VDDQ VDDQ VDDQ VDDQ VDDQ A13 A12
10 A8 A9 NC I/O15 I/O13 I/O11 I/O9 NC I/O7 I/O5 I/O3 I/O1 NC A14 A15
11 NC NC(3) I/OP2 I/O14 I/O12 I/O10 I/O8 ZZ(2) I/O6 I/O4 I/O2 I/O0 I/OP1 A17 A16
5309tbl 17a
NC I/OP3 I/O17 I/O19 I/O21 I/O23 VSS (1) I/O25 I/O27 I/O29 I/O31 I/OP4 NC LBO
NC(3)
DNU(4)
DNU(4)
Pin Configuration 512K x 18, 165 fBGA
1 A B C D E F G H J K L M N P R NC(3) NC NC NC NC NC NC VSS (1) I/O12 I/O13 I/O14 I/O15 I/OP2 NC LBO 2 A7 A6 NC I/O8 I/O9 I/O10 I/O11 NC NC NC NC NC NC NC
(3)
3 CE CS0 VDDQ VDDQ VDDQ VDDQ VDDQ NC VDDQ VDDQ VDDQ VDDQ VDDQ A5 A4
4 BW2 NC VSS VDD VDD VDD VDD VDD VDD VDD VDD VDD VSS A2 A3
5 NC BW1 VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS NC DNU
(4)
6 CS1 CLK VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS NC
(3)
7 BWE GW VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS NC DNU
(4)
8 ADSC OE VSS VDD VDD VDD VDD VDD VDD VDD VDD VDD VSS A11 A12
9 ADV ADSP VDDQ VDDQ VDDQ VDDQ VDDQ NC VDDQ VDDQ VDDQ VDDQ VDDQ A14 A13
10 A8 A9 NC NC NC NC NC NC I/O3 I/O2 I/O1 I/O0 NC A15 A16
11 A10 NC(3) I/OP1 I/O7 I/O6 I/O5 I/O4 ZZ(2) NC NC NC NC NC A18 A17
5309 tbl 17b
A1 A0
NC(3)
DNU(4)
DNU(4)
NOTES: 1. H1 does not have to be directly connected to VSS, as long as the input voltage is < VIL. 2. H11 can be left unconnected and the device will always remain in active mode. 3. Pin N6, B11, A1, R2 and P2 are reserved for 18M, 36M, 72M, and 144M and 288M respectively. 4. DNU= Do not use; these signals can either be left unconnected or tied to Vss.
6.42 8
IDT71V67703, IDT71V67903, 256K x 36, 512K x 18, 3.3V Synchronous SRAMS with 3.3V I/O, Flow-Through Outputs, Single Cycle Deselect Commercial and Industrial Temperature Ranges
DC Electrical Characteristics Over the Operating Temperature and Supply Voltage Range (VDD = 3.3V 5%)
Symbol |ILI| |ILI| |ILO| VOL VOH Parameter Input Leakage Current LBO Input Leakage Current(1) Output Leakage Current Output Low Voltage Output High Voltage Test Conditions VDD = Max., VIN = 0V to VDD VDD = Max., VIN = 0V to VDD VOUT = 0V to VCC IOL = +8mA, VDD = Min. IOH = -8mA, VDD = Min. Min.
___
Max. 5 30 5 0.4
___
Unit A A A V V
5309 tbl 08
___ ___ ___
2.4
NOTE: 1. The LBO pin will be internally pulled to VDD if it is not actively driven in the application and the ZZ in will be internally pulled to VSS if not actively driven.
DC Electrical Characteristics Over the Operating Temperature and Supply Voltage Range (1)
7.5ns Symbol IDD ISB1 ISB2 IZZ Parameter Operating Power Supply Current Test Conditions Device Se lected, Outputs Open, VDD = Max., VDDQ = Max., VIN > VIH or < VIL, f = fMAX(2) Com'l 265 50 145 50 Ind 285 70 165 70 8ns Com'l 210 50 140 50 Ind 230 70 160 70 8.5ns Unit Com'l 190 50 135 50 Ind mA 210 mA 70 mA 155 70 mA
5309 tbl 09
CMOS Standby Power Supply Current Device Deselected, Outputs Open, VDD = Max., VDDQ = Max., VIN > VHD or < VLD, f = 0(2,3) Clock Running Power Supply Current Full Sleep Mode Supply Current Device Deselected, Outputs Open, VDD = Max., VDDQ = Max., VIN > VHD or < VLD, f = fMAX (2,.3) ZZ > VHD, VDD = Max.
NOTES: 1. All values are maximum guaranteed values. 2. At f = fMAX, inputs are cycling at the maximum frequency of read cycles of 1/tCYC while ADSC = LOW; f=0 means no input lines are changing. 3. For I/Os VHD = VDDQ - 0.2V, VLD = 0.2V. For other inputs VHD = VDD - 0.2V, VLD = 0.2V.
AC Test Conditions
(VDDQ = 3.3V/2.5V)
Input Pulse Levels Input Rise/Fall Times Input Timing Reference Levels Output Timing Reference Levels AC Test Load 0 to
3V
AC Test Load
2ns 1.5V 1.5V See Figure 1
5309 tbl 10
VDDQ/2 50
I/O
Z0 = 50
5309 drw 03
,
6 5 4 3 tCD (Typical, ns) 2 1 20 30 50 80 100 Capacitance (pF) 200
5309 drw 05
Figure 1. AC Test Load
,
Figure 2. Lumped Capacitive Load, Typical Derating
6.42 9
IDT71V67703, IDT71V67903, 256K x 36, 512K x 18, 3.3V Synchronous SRAMS with 3.3V I/O, Flow-Through Outputs, Single Cycle Deselect Commercial and Industrial Temperature Ranges
Synchronous Truth Table (1,3)
Operation Deselected Cycle, Power Down Deselected Cycle, Power Down Deselected Cycle, Power Down Deselected Cycle, Power Down Deselected Cycle, Power Down Read Cycle, Begin Burst Read Cycle, Begin Burst Read Cycle, Begin Burst Read Cycle, Begin Burst Read Cycle, Begin Burst Write Cycle, Begin Burst Write Cycle, Begin Burst Read Cycle, Continue Burst Read Cycle, Continue Burst Read Cycle, Continue Burst Read Cycle, Continue Burst Read Cycle, Continue Burst Read Cycle, Continue Burst Read Cycle, Continue Burst Read Cycle, Continue Burst Write Cycle, Continue Burst Write Cycle, Continue Burst Write Cycle, Continue Burst Write Cycle, Continue Burst Read Cycle, Suspend Burst Read Cycle, Suspend Burst Read Cycle, Suspend Burst Read Cycle, Suspend Burst Read Cycle, Suspend Burst Read Cycle, Suspend Burst Read Cycle, Suspend Burst Read Cycle, Suspend Burst Write Cycle, Suspend Burst Write Cycle, Suspend Burst Write Cycle, Suspend Burst Write Cycle, Suspend Burst
NOTES: 1. L = VIL, H = VIH, X = Don't Care. 2. OE is an asynchronous input. 3. ZZ - low for the table.
Address Used None None None None None External External External External External External External Next Next Next Next Next Next Next Next Next Next Next Next Current Current Current Current Current Current Current Current Current Current Current Current
CE H L L L L L L L L L L L X X X X H H H H X X H H X X X X H H H H X X H H
CS0 X X L X L H H H H H H H X X X X X X X X X X X X X X X X X X X X X X X X
CS1 X H X H X L L L L L L L X X X X X X X X X X X X X X X X X X X X X X X X
ADSP X L L X X L L H H H H H H H H H X X X X H H X X H H H H X X X X H H X X
ADSC L X X L L X X L L L L L H H H H H H H H H H H H H H H H H H H H H H H H
ADV X X X X X X X X X X X X L L L L L L L L L L L L H H H H H H H H H H H H
GW X X X X X X X H H H H L H H H H H H H H H L H L H H H H H H H H H L H L
BWE X X X X X X X H L L L X H H X X H H X X L X L X H H X X H H X X L X L X
BWx X X X X X X X X H H L X X X H H X X H H L X L X X X H H X X H H L X L X
OE(2) X X X X X L H L L H X X L H L H L H L H X X X X L H L H L H L H X X X X
CLK
I/O HI-Z HI-Z HI-Z HI-Z HI-Z DOUT HI-Z DOUT DOUT HI-Z DIN DIN DOUT HI-Z DOUT HI-Z DOUT HI-Z DOUT HI-Z DIN DIN DIN DIN DOUT HI-Z DOUT HI-Z DOUT HI-Z DOUT HI-Z DIN DIN DIN DIN
5309 tbl 11
6.42 10
IDT71V67703, IDT71V67903, 256K x 36, 512K x 18, 3.3V Synchronous SRAMS with 3.3V I/O, Flow-Through Outputs, Single Cycle Deselect Commercial and Industrial Temperature Ranges
Synchronous Write Function Truth Table (1, 2)
Operation Read Read Write all Bytes Write all Bytes Write Byte 1 Write Byte 2 Write Byte 3 Write Byte 4
(3) (3) (3) (3)
GW H H L H H H H H
BWE H L X L L L L L
BW1 X H X L L H H H
BW2 X H X L H L H H
BW3 X H X L H H L H
BW4 X H X L H H H L
5309 tbl 12
NOTES: 1. L = VIL, H = VIH, X = Don't Care. 2. BW3 and BW4 are not applicable for the IDT71V67903. 3. Multiple bytes may be selected during the same cycle.
Asynchronous Truth Table (1)
Operation (2) Read Read Write Deselected Sleep Mode OE L H X X X ZZ L L L L H I/O Status Data Out High-Z High-Z - Data In High-Z High-Z Power Active Active Active Standby Sleep
5309 tbl 13
NOTES: 1. L = VIL, H = VIH, X = Don't Care. 2. Synchronous function pins must be biased appropriately to satisfy operation requirements.
Interleaved Burst Sequence Table ( LBO=VDD)
Sequence 1 A1 First Address Second Address Third Address Fourth Address (1) 0 0 1 1 A0 0 1 0 1 Sequence 2 A1 0 0 1 1 A0 1 0 1 0 Sequence 3 A1 1 1 0 0 A0 0 1 0 1 Sequence 4 A1 1 1 0 0 A0 1 0 1 0
5309 tbl 14
NOTE: 1. Upon completion of the Burst sequence the counter wraps around to its initial state.
Linear Burst Sequence Table ( LBO=VSS)
Sequence 1 A1 First Address Second Address Third Address Fourth Address (1) 0 0 1 1 A0 0 1 0 1 Sequence 2 A1 0 1 1 0 A0 1 0 1 0 Sequence 3 A1 1 1 0 0 A0 0 1 0 1 Sequence 4 A1 1 0 0 1 A0 1 0 1 0
5309 tbl 15
NOTE: 1. Upon completion of the Burst sequence the counter wraps around to its initial state.
6.42 11
IDT71V67703, IDT71V67903, 256K x 36, 512K x 18, 3.3V Synchronous SRAMS with 3.3V I/O, Flow-Through Outputs, Single Cycle Deselect Commercial and Industrial Temperature Ranges
AC Electrical Characteristics (VDD = 3.3V 5%, Commercial and Industrial
Temperature Ranges)
7.5ns Symbol Parameter Min. Max. Min. 8ns Max. 8.5ns Min. Max. Unit
Clock Parameter
tCYC tCH(1) tCL(1) Clock Cycle Time Clock High Pulse Width Clock Low Pulse Width 8.5 3 3
____
10 4 4
____
11.5 4.5 4.5
____
ns ns ns
____
____
____
____
____
____
Output Parameters
tCD tCDC tCLZ(2) tCHZ(2) tOE tOLZ(2) tOHZ(2) Clock High to Valid Data Clock High to Data Change Clock High to Output Active Clock High to Data High-Z Output Enable Access Time Output Enable Low to Output Active Output Enable High to Output High-Z
____
7.5
____
____
8
____
____
8.5
____
ns ns ns ns ns ns ns
2 0 2
____
2 0 2
____
2 0 2
____
____
____
____
3.5 3.5
____
3.5 3.5
____
3.5 3.5
____
0
____
0
____
0
____
3.5
3.5
3.5
Set Up Times
tSA tSS tSD tSW tSAV tSC Address Setup Time Address Status Setup Time Data In Setup Time Write Setup Time Address Advance Setup Time Chip Enable/Select Setup Time 1.5 1.5 1.5 1.5 1.5 1.5
____
2 2 2 2 2 2
____
2 2 2 2 2 2
____
ns ns ns ns ns ns
____ ____
____ ____
____ ____
____ ____
____ ____
____ ____
____
____
____
Hold Times
tHA tHS tHD tHW tHAV tHC Address Hold Time Address Status Hold Time Data In Hold Time Write Hold Time Address Advance Hold Time Chip Enable/Select Hold Time 0.5 0.5 0.5 0.5 0.5 0.5
____ ____
0.5 0.5 0.5 0.5 0.5 0.5
____ ____
0.5 0.5 0.5 0.5 0.5 0.5
____ ____
ns ns ns ns ns ns
____
____
____
____ ____
____ ____
____ ____
____
____
____
Sleep Mode and Configuration Parameters
tZZPW tZZR(3) tCFG (4) ZZ Pulse Width ZZ Recovery Time Configuration Set-up Time 100 100 34
____ ____
100 100 40
____ ____
100 100 50
____ ____
ns ns ns
5309 tbl 16
____
____
____
NOTES: 1. Measured as HIGH above VIH and LOW below VIL. 2. Transition is measured 200mV from steady-state. 3. Device must be deselected when powered-up from sleep mode. 4. tCFG is the minimum time required to configure the device based on the LBO input. LBO is a static input and must not change during normal operation.
6.42 12
tCYC
CLK tCH tCL
tSS tHS
ADSP
ADSC tHA Ax tSW tHW Ay
(1)
tSA
ADDRESS
GW, BWE, BWx tHC tSAV tHAV
tSC
CE, CS1
(Note 3)
ADV tOE tCD tOHZ tOLZ
O1(Ax) O1(Ay) O2(Ay)
ADV HIGH suspends burst
Timing Waveform of Flow-Through Read Cycle (1,2)
IDT71V67703, IDT71V67903, 256K x 36, 512K x 18, 3.3V Synchronous SRAMS with 3.3V I/O, Flow-Through Outputs, Single Cycle Deselect Commercial and Industrial Temperature Ranges
6.42 13
tCDC
O3(Ay)
OE
(Burst wraps around to its initial state)
tCHZ
O4(Ay) O1(Ay) O2(Ay)
DATAOUT
Output Disabled Flow-through Read
Burst Flow-through Read
5309 drw 06
NOTES: 1. O1 (Ax) represents the first output from the external address Ax. O1 (Ay) represents the first output from the external address Ay; O2 (Ay) represents the next output data in the burst sequence of the base address Ay, etc. where A0 and A1 are advancing for the four word burst in the sequence defined by the state of the LBO input. 2. ZZ input is LOW and LBO is Don't Care for this cycle. 3. CS0 timing transitions are identical but inverted to the CE and CS1 signals. For example, when CE and CS1 are LOW on this waveform, CS0 is HIGH.
,
tCYC
CLK tCH tCL
(2)
tSS tHS
ADSP
tSA tHA Ax Ay tSW tHW Az
ADDRESS
GW
ADV
OE tSD tHD tOE tCD tOLZ tOHZ O1(Ax) tCD Write I1(Ay) tCLZ
Timing Waveform of Combined Flow-Through Read and Write Cycles (1,2,3)
IDT71V67703, IDT71V67903, 256K x 36, 512K x 18, 3.3V Synchronous SRAMS with 3.3V I/O, Flow-Through Outputs, Single Cycle Deselect Commercial and Industrial Temperature Ranges
6.42 14
DATAIN
tCDC O1(Az) O2(Az) O3(Az) O4(Az)
DATAOUT
Single Read
Flow-through Burst Read
5309 drw 07
NOTES: 1. Device is selected through entire cycle; CE and CS1 are LOW, CS0 is HIGH. 2. ZZ input is LOW and LBO is Don't Care for this cycle. 3. O1 (Ax) represents the first output from the external address Ax. I1 (Ay) represents the first input from the external address Ay; O1 (Az) represents the first output from the external address Az; O2 (Az) represents the next output data in the burst sequence of the base address Az, etc. where A0 and A1 are advancing for the four word burst in the sequence defined by the state of the LBO input.
,
tCYC
CLK tCH tCL
tSS tHS
ADSP
(1)
ADSC
tSA tHA Ax
GW is ignored when ADSP initiates a cycle and is sampled on the next cycle rising edge
ADDRESS Ay
Az tHW tSW
GW
tSC
tHC
CE, CS1 tSAV tHAV
(Note 3)
Timing Waveform of Write Cycle No. 1 - GW Controlled (1,2,3)
IDT71V67703, IDT71V67903, 256K x 36, 512K x 18, 3.3V Synchronous SRAMS with 3.3V I/O, Flow-Through Outputs, Single Cycle Deselect Commercial and Industrial Temperature Ranges
6.42 15
(ADV suspends burst)
ADV
OE tSD I1(Ax) tOHZ I1(Ay) I2(Ay) I2(Ay)
(2)
tHD
DATAIN
I3(Ay)
I4(Ay)
I1(Az)
I2(Az)
I3(Az)
DATAOUT
O3(Aw)
O4(Aw)
5309 drw 08
NOTES: 1. ZZ input is LOW, BWE is HIGH and LBO is Don't Care for this cycle. 2. O4 (Aw) represents the final output data in the burst sequence of the base address Aw. I1 (Ax) represents the first input from the external address Ax. I1 (Ay) represents the first input from the external address Ay; I2 (Ay) represents the next input data in the burst sequence of the base address Ay, etc. where A0 and A1 are advancing for the four word burst in the sequence defined by the state of the LBO input. In the case of input I2 (Ay) this data is valid for two cycles because ADV is high and has suspended the burst. 3. CS0 timing transitions are identical but inverted to the CE and CS1 signals. For example, when CE and CS1 are LOW on this waveform, CS0 is HIGH.
,
tCYC
CLK tCH tCL
tSS tHS
ADSP
ADSC
tSA tHA Ax
BWE is ignored when ADSP initiates a cycle and is sampled on the next cycle rising edge
ADDRESS
Ay Az
tHW tSW
BWE
BWx is ignored when ADSP initiates a cycle and is sampled on the next clock rising edge
tHW tSW
BWx
tSC
tHC
CE, CS1 tSAV
(Note 3)
Timing Waveform of Write Cycle No. 2 - Byte Controlled
IDT71V67703, IDT71V67903, 256K x 36, 512K x 18, 3.3V Synchronous SRAMS with 3.3V I/O, Flow-Through Outputs, Single Cycle Deselect Commercial and Industrial Temperature Ranges
6.42 16
(ADV HIGH suspends burst)
ADV
OE tSD I1(Ax) tOHZ I1(Ay) I2(Ay) I2(Ay) I3(Ay) I4(Ay) I1(Az)
tHD
DATAIN
I2(Az)
I3(Az)
DATAOUT Single Write
O3(Aw)
O4(Aw) Burst Write Extended Burst Write
5309 drw 09
Burst Read
(1,2,3)
NOTES: 1. ZZ input is LOW, GW is HIGH and LBO is Don't Care for this cycle. 2. O4 (Aw) represents the final output data in the burst sequence of the base address Aw. I1 (Ax) represents the first input from the external address Ax. I1 (Ay) represents the first input from the external address Ay; I2 (Ay) represents the next input data in the burst sequence of the base address Ay, etc. where A0 and A1 are advancing for the four word burst in the sequence defined by the state of the LBO input. In the case of input I2 (Ay) this data is valid for two cycles because ADV is high and has suspended the burst. 3. CS0 timing transitions are identical but inverted to the CE and CS1 signals. For example, when CE and CS1 are LOW on this waveform, CS0 is HIGH.
,
tCYC
CLK tCH tCL
tSS
tHS
ADSP
ADSC tHA Ax Az
tSA
ADDRESS
GW tHC
tSC
CE, CS1
(Note 4)
ADV
tOE
Timing Waveform of Sleep (ZZ) and Power-Down Modes (1,2,3)
IDT71V67703, IDT71V67903, 256K x 36, 512K x 18, 3.3V Synchronous SRAMS with 3.3V I/O, Flow-Through Outputs, Single Cycle Deselect Commercial and Industrial Temperature Ranges
6.42 17
O1(Ax)
tZZPW
OE
tOLZ
DATAOUT
tZZR
ZZ
Single Read
Snooze Mode
5309 drw 13
,
NOTES: 1. Device must power up in deselected Mode. 2. LBO is Don't Care for this cycle. 3. It is not necessary to retain the state of the input registers throughout the Power-down cycle. 4. CS0 timing transitions are identical but inverted to the CE and CS1 signaals. For example, when CE and CS1 are LOW
on this waveform, CS0 is HIGH.
IDT71V67703, IDT71V67903, 256K x 36, 512K x 18, 3.3V Synchronous SRAMS with 3.3V I/O, Flow-Through Outputs, Single Cycle Deselect Commercial and Industrial Temperature Ranges
Non-Burst Read Cycle Timing Waveform
CLK
ADSP
ADSC
ADDRESS
Av
Aw
Ax
Ay
Az
GW, BWE, BWx
CE, CS1
CS0
OE
DATAOUT
(Av)
(Aw)
(Ax)
(Ay)
5309 drw 10
NOTES: 1. ZZ input is LOW, ADV is HIGH and LBO is Don't Care for this cycle. 2. (Ax) represents the data for address Ax, etc. 3. For read cycles, ADSP and ADSC function identically and are therefore interchangable.
,
Non-Burst Write Cycle Timing Waveform
CLK
ADSP
ADSC
ADDRESS
Av
Aw
Ax
Ay
Az
GW
CE, CS1
CS0
DATAIN
(Av)
(Aw)
(Ax)
(Ay)
(Az)
,
5309 drw 11
NOTES: 1. ZZ input is LOW, ADV and OE are HIGH, and LBO is Don't Care for this cycle. 2. (Ax) represents the data for address Ax, etc. 3. Although only GW writes are shown, the functionality of BWE and BWx together is the same as GW. 4. For write cycles, ADSP and ADSC have different limitations.
6.42 18
IDT71V67703, IDT71V67903, 256K x 36, 512K x 18, 3.3V Synchronous SRAMS with 3.3V I/O, Flow-Through Outputs, Single Cycle Deselect Commercial and Industrial Temperature Ranges
100-Pin Thin Plastic Quad Flatpack (TQFP) Package Diagram Outline
6.42 19
IDT71V67703, IDT71V67903, 256K x 36, 512K x 18, 3.3V Synchronous SRAMS with 3.3V I/O, Flow-Through Outputs, Single Cycle Deselect Commercial and Industrial Temperature Ranges
119 Ball Grid Array (BGA) Package Diagram Outline
6.42 20
IDT71V67703, IDT71V67903, 256K x 36, 512K x 18, 3.3V Synchronous SRAMS with 3.3V I/O, Flow-Through Outputs, Single Cycle Deselect Commercial and Industrial Temperature Ranges
165 Fine Pitch Ball Grid Array (fBGA) Package Diagram Outline
6.42 21
IDT71V67703, IDT71V67903, 256K x 36, 512K x 18, 3.3V Synchronous SRAMS with 3.3V I/O, Flow-Through Outputs, Single Cycle Deselect Commercial and Industrial Temperature Ranges
Ordering Information
IDT XXX Device Type S Power X Speed XX Package X Process/ Temperature Rance Commercial (0C to +70C) Industrial (-40C to +85C) 100-Pin Plastic Thin Quad Flatpack (TQFP) 119 Ball Grid Array (BGA) 165 fine pitch Ball Grid Array (fBGA)
Blank I PF BG BQ
75 80 85
Access Time in Tenths of Nanoseconds
71V67703 71V67903
256K x 36 Flow-Through Burst Synchronous SRAM 512K x 18 Flow-Through Burst Synchronous SRAM
5309 drw 12
,
6.42 22
IDT71V67703, IDT71V67903, 256K x 36, 512K x 18, 3.3V Synchronous SRAMS with 3.3V I/O, Flow-Through Outputs, Single Cycle Deselect Commercial and Industrial Temperature Ranges
Datasheet Document History
12/31/99 04/26/00 Pg. 4 Pg. 7 Pg. 18 05/24/00 Pg. 1,4,8,21 22 Pg. 5,6,7,8 Pg. 20 Pg. 5,6,8 Pg. 7 Pg. 20 Pg. 9 Pg. 1,2 Pg. 7 Pg. 8 Pg. 9 Pg. 1-23 Pg. 4,9,12, 22 Pg.4 Created Datasheet from 71V677 and 71V679 Datasheets For 2.5V I/O offering, see 71V67702 AND 71V67902 Datasheets. Add capacitance for BGA package; Insert clarification note to Absolute Max Ratings and Recommended Operating Temperature tables. Replace Pin U6 with TRST pin in BGA pin configuration; Add pin description note in pinout Inserted 100 pin TQFP Package Diagram Outline Add new package offering, 13 x 15 fBGA Correct note 2 on BGA and TQFP pin configuration Correction in the 119 BGA Package Diagram Outline Remove note from TQFP and BQ165 pinouts Add/Remove note from BG119 pinout Update BG 119 pinout Updated ISB2 levels for 7.5-8.5ns. Remove JTAG pins Changed U2-U6 pins to DNU. Changed P5,P7,R5 & R7 to DNU pins. Raised specs by 10mA on 7.5ns, 8ns and 8.5ns. Changed datasheet from Advanced to Final Release. Added I temp to datasheet. Updated 165 fBGA table from TBD to 7.
07/12/00
12/18/00 10/29/01
10/22/02
04/15/03
CORPORATE HEADQUARTERS 2975 Stender Way Santa Clara, CA 95054
for SALES: 800-345-7015 or 408-727-6116 fax: 408-492-8674 www.idt.com
for Tech Support: sramhelp@idt.com 800-544-7726, x4033
The IDT logo is a registered trademark of Integrated Device Technology, Inc.
6.42 23


▲Up To Search▲   

 
Price & Availability of IDT71V67703

All Rights Reserved © IC-ON-LINE 2003 - 2022  

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]


 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X